- Manuals
- Brands
- NetZero Manuals
- Indoor Fireplace
- KALFIRE E-one 190F
- Installation and operation manual
Hide thumbs
-
- Contents
- Table of Contents
- Bookmarks
Table of Contents
-
Table of Contents
-
Introduction
-
Receiving Inspection
-
Certification
-
General Safety Regulations
-
Additional General Safety Regulations for Atmos Heating
-
Disposal
-
California Proposition 65 Warning
-
Assembly of the Fireplace
-
Required Tools
-
Included Hardware
-
Removal of Covers
-
Adjustable Feet
-
Rear Screen Assembly
-
Top Screen Assembly
-
Installing the Fireplace
-
Light / Illumination
-
Viewing Height
-
Connecting Fireplace to Power
-
Framing Dimensions
-
Wall Dimensions
-
Mantel Installation
-
TV Installation
-
Setting up the Fireplace
-
Flat Bottom Plate
-
Placing Lower Sidewalls
-
Log Set Installation
-
Placing Glass Reflector
-
Placing Upper Side Walls
-
Placing Front Window
-
One Operation
-
Main On/Off Switch
-
Hotel Switch
-
Remote Control Pairing
-
E-One Remote and Symbols
-
Kalfire Connected App
-
Installing the Kalfire Connected App
-
Maintenance
-
Cleaning the Fireplace
-
Cleaning the Glass Reflector
-
Warranty
-
Technical Data
-
Specifications
-
Serial Number Label
-
Wire Diagram
-
Dimension Drawing
Advertisem*nt
Quick Links
Download this manual
INSTALLATION AND OPERATION MANUAL
Please read these instructions completely before
installing or operating the E-one fireplace.
NetZero Kalfire E-one Electric Fireplace
Models: AA-11-05539 – E-one 190F
IMPORTANT
Please read these instructions carefully before installation.
Failure to follow them could result in serious injury.
This appliance must be installed by a qualified installer.
The installation and wiring connections must be done in accordance with the
national and local codes having jurisdiction.
For use with 120V 60Hz electrical supply only.
This appliance must be grounded.
The heater outlet becomes hot while in operation.
Never cover the heater outlet or any other part of the appliance.
SAVE THESE INSTRUCTIONS
85-03-01306
NetZero Fireplace ©2024 All rights reserved. 0324
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for NetZero KALFIRE E-one 190F
-
Indoor Fireplace NetZero Kalfire E-one 130F Installation And Operation Manual
(20 pages)
-
Indoor Fireplace NetZero Kalfire E-one 130B Installation And Operation Manual
(20 pages)
-
Indoor Fireplace NetZero Kalfire E-one 160F Installation And Operation Manual
(22 pages)
-
Indoor Fireplace NetZero Kalfire E-one AA-11-05388 - E-one 100F Installation And Operation Manual
(20 pages)
-
Indoor Fireplace NetZero Kalfire E-one AA-11-05387-E-one 130F Installation And Operation Manual
(20 pages)
-
Indoor Fireplace NetZero Kalfire E-one AA-11-05386-E-one 130B Installation And Operation Manual
(20 pages)
-
Indoor Fireplace NetZero Burner Series Installation Manual
(16 pages)
-
Indoor Fireplace NetZero Waterplace Series Installation Manual
(16 pages)
-
Indoor Fireplace NetZero E-one 100 Installation And Operation Manual
(18 pages)
-
Indoor Fireplace NetZero Firebox Series Installation Manual
Waterplace and waterplace platinum (15 pages)
-
Indoor Fireplace NetZero Firebox Series Installation Manual
(20 pages)
Summary of Contents for NetZero KALFIRE E-one 190F
- Page 1 For use with 120V 60Hz electrical supply only. This appliance must be grounded. The heater outlet becomes hot while in operation. Never cover the heater outlet or any other part of the appliance. SAVE THESE INSTRUCTIONS 85-03-01306 NetZero Fireplace ©2024 All rights reserved. 0324...
-
Page 2: Table Of Contents
Table of contents 1 INTRODUCTION 1.1 Receiving Inspection 1.2 Certification 2 GENERAL SAFETY REGULATIONS 2.1 Additional General Safety Regulations for Atmos Heating 2.2 Disposal 2.3 California Proposition 65 Warning 3 ASSEMBLY OF THE FIREPLACE 3.1 Required Tools 3.2 Included Hardware 3.3 Removal of Covers 3.4 Adjustable Feet 3.1 Rear Screen Assembly... -
Page 3: Introduction
However, there is no NetZero Fire stands for innovation and quality. This is why guarantee that interference will not occur in a particular we work continuously on the further development of our installation. -
Page 4: Additional General Safety Regulations For Atmos Heating
Do not place the fireplace directly under a wall • the heater above the heater. NetZero Fire will not socket or junction box. be responsible for any damage to these items. -
Page 5: Assembly Of The Fireplace
ASSEMBLY OF THE FIREPLACE Rear Screen Assembly Install the rear screen bracket to the top LED rear screen Required Tools bracket. Use 4 (M5 x 10) screws. - 8mm Nut Driver or Socket - 3mm Allen Wrench - 12mm Wrench - 17mm Wrench - Level Included Hardware... - Page 6 Connect the two rear screen: Remove the protective film from the rear screen mask. This is the plexiglass sheet with three tabs at the top. The mask 1. HDMI will hang on the tabs at the top of the rear bracket. The tabs 2.
-
Page 7: Top Screen Assembly
Top Screen Assembly Replace the rear and top panels with 8 (M5 x 10) screws. The fireplace in now ready to be installed into your wall. Remove the protective film from the top screen before installing it into the fireplace. The pegs at the front of the screen rest on brackets as shown below. -
Page 8: Installing The Fireplace
INSTALLING THE FIREPLACE Framing Dimensions Recommended framing is shown below. Minimum space requirement to fit the fireplace are: Light / Illumination Width – 75 3/8” Height – 34 ½” Depth – 18” The E-one functions on the basis of hologram technology. This involves the use of a glass reflector that is placed at an The ceiling of the enclosure must be at least 6”... -
Page 9: Wall Dimensions
Temperatures above the heat outlet on the fireplace can reach temperatures up to 150°F. Materials used in this area must be rated for these temperatures. NetZero Fire is not responsible for damage to walls because of the use of improper materials or installation. -
Page 10: Setting Up The Fireplace
SETTING UP THE FIREPLACE Placing Lower Sidewalls The lower sidewalls fit into the fireplace as shown below. Place the fireplace in its final position before continuing to The sidewall will sit flat on the floor of the fireplace. The set up the fireplace. front flange of the sidewall will sit behind the guide at the Level the fireplace using the adjustable legs. -
Page 11: Log Set Installation
Log Set Installation The logs are made of fragile material. Therefore, proceed with extreme caution when installing the logs. NOTE: Log set instructions are shown with the flat bottom floor installed in the fireplace. When installing the log set it is important that the logs are places exactly as shown in these instructions. If logs are not placed correctly the projected flame will not line up with the logs. - Page 12 Start the log set installation by placing the ember bed and floor as shown below. Place the next three logs “K”, “D”, and “Q” on the ember bed grooves as shown. Next place log “G” on top of log “D”. Once “G” is place, add “S”, “T”, “J”, and “F” in their groove as shown below.
- Page 13 Next place logs “R”, “V”, and “U” as shown below. To finish the installation, sprinkle the vermiculite and lava stones over the ember bed. First place the lava stones between and around the logs. Then sprinkle vermiculite over the entire ember bed as well as on the floor plate around the ember bed. If too much vermiculite is placed on the ember bed the light of the ember bed will not be visible.
-
Page 14: Placing Glass Reflector
Placing Upper Side Walls Placing Glass Reflector Install the upper side walls in the fireplace. Install the side walls by placing the bottom point against the extrusion on the glass reflector. Then rotate the side wall towards the wall and the magnet will hold it in place. The glass reflector is susceptible to stains and fingerprints. -
Page 15: One Operation
Wear the included gloves to handle the front window. Place Hotel Switch the front window into the two holders at the front of the The fireplace can be switched On/Off by means of an fireplace. Then rotate the window up. Slide the loosened external switch. -
Page 16: E-One Remote And Symbols
E-One Remote and Symbols Kalfire has pre-set and recorded 3 moods under the respective Mood buttons. Atmos Heating (ON/OFF switch) The specially developed Atmos Heating element provides a Power Button pleasant atmospheric warmth, contributing to the ultra- This button has three functions: On, Anti-Reflect, Off. realistic fire experience. -
Page 17: Kalfire Connected App
KALFIRE CONNECTED APP Cleaning The Glass Reflector The glass reflector that is placed at an angle in the fireplace The Kalfire Connected app offers more and extended must be treated with care. possibilities compared to the remote control. Instructions for cleaning the glass reflector: Installing the Kalfire Connected App Before installing the Kalfire Connected app, Please Check: •... -
Page 18: Warranty
NetZero Fire is not responsible for results or costs of workmanship of unauthorized NetZero Fire dealers or agents in the negligence of their service work. -
Page 19: Wire Diagram
10.3 Wire Diagram... -
Page 20: Dimension Drawing
10.4 Dimension Drawing For framing the fireplace follow the framing dimensions and instructions given in this manual. Warning: The ceiling of the enclosure must be at least 6” above the top of the heater or 11 ½” above the top of the fireplace. - Page 22 1155 Sherman Rd, Hiawatha, IA 52233 (800)553-5422 NetZero is a manufactureer and distributor of these products, which are designed by Kalfire B.V. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND SUPPLIED MANUALS. IMPLIED WARRANTIES OF MERCHANTABILITY, IMPLIED WARRANTIES OF FITNESS, IMPLIED...
This manual is also suitable for:
Aa-11-05539
